75. Valves & CocksDIN Pressure Reducing ValvesPressure Reducing Valves Gunmetal & Stainless Steel with Threaded Connection
Pressure Reducing Valves Gunmetal & Stainless Steel with Threaded Connection
756561 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-SP DN15
IMPA:756561
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756562 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-SP DN20
IMPA:756562
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756563 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-SP DN25
IMPA:756563
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756564 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-SP DN32
IMPA:756564
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756565 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-SP DN40
IMPA:756565
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756566 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-SP DN50
IMPA:756566
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756643 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-LP DN15
IMPA:756643
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756644 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-LP DN20
IMPA:756644
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756653 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-LP DN25
IMPA:756653
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756654 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-LP DN32
IMPA:756654
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756663 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-LP DN40
IMPA:756663
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756664 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-LP DN50
IMPA:756664
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756697 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-HP DN15
IMPA:756697
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756698 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-HP DN20
IMPA:756698
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756699 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-HP DN25
IMPA:756699
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756916 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-HP DN32
IMPA:756916
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756917 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-HP DN40
IMPA:756917
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756918 VALVE PRESSURE REDUCING DIN, GUNMETAL #681MGFO-HP DN50
IMPA:756918
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756919 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-LP DN15
IMPA:756919
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756920 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-LP DN20
IMPA:756920
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756927 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-LP DN25
IMPA:756927
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756928 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-LP DN32
IMPA:756928
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756929 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-LP DN40
IMPA:756929
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756930 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-LP DN50
IMPA:756930
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756937 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-SP DN15
IMPA:756937
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756938 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-SP DN20
IMPA:756938
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756939 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-SP DN25
IMPA:756939
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756940 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-SP DN32
IMPA:756940
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756949 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-SP DN40
IMPA:756949
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756950 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-SP DN50
IMPA:756950
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756959 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-HP DN15
IMPA:756959
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756960 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-HP DN20
IMPA:756960
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756968 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-HP DN25
IMPA:756968
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756969 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-HP DN32
IMPA:756969
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756970 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-HP DN40
IMPA:756970
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
756978 VALVE PRESSURE REDUCING DIN, S.STEEL #481MGFO-HP DN50
IMPA:756978
MTML UOM:PCE
Marine Type Approvals held for these valves: American Bureau of Shipping, Bureau Veritas, Germanischer Lloyd, Lloyds Register. Pressure reducer with threaded connections made of gunmetal with pressure-relieved single seat valve and built-in dirt trap. Spring made of rust resistant, and strainers made of stainless steel. Diaphragm made of high-quality plastic with insert of fabric, and gasket made of heat resistant-plastic. Body with G 1/4” connection for pressure gauge on both sides. Standard thread: BSPTm also available in female BSP-P for sizes up to 1”(PLEASE CLEARLY INDICATE IN THE ORDER:“f/f” or “BSPTm/BSPTm”). Available three models with EPDM (ethylene propylene diene monomer rubber) seal suitable for water, neutral and non-sticking liquids, compressed air and neutral gases, FKM (Fluoroelastomer) seal suitable for non-neutral media i.e. oils, fuels, oil-laden compressed air, etc., Low Pressure: 681/481mGFO-LP EPDM and FKM, Standard Pressure: 681/481mGFO-SP EPDM and FKM, High Pressure: 681/481mGFO-HP EPDM and FKM. Mesh sizes: G1/2” to G 1-1/4” = 0.6 mm, DN40 and DN50 = 0.75 mm. Seats for version 681: DN15 to DN20 made of stainless steel, DN32 to DN50 made of gunmetal, Primary pressure: up to 40 bar, Secondary pressure: 0.5 - 15 bar. All models also available in Stainless Steel: series 481. Model 681mGFO-LP (Low Pressure)
© 2025 ShipServ Limited